Vimarsana
Biggest News Aggregation in the World

Page 9 - Mechanical Properties News Today : Breaking News, Live Updates & Top Stories | Vimarsana

Stay updated with breaking news from Mechanical Properties. Get real-time updates on events, politics, business, and more. Visit us for reliable news and exclusive interviews.

Top News In Mechanical Properties Today - Breaking & Trending Today

"Additive manufacturing of a functionally graded high entropy alloy usi" by Yao Lu, Jun Wang et al. - Vimarsana News

"Additive manufacturing of a functionally graded high entropy alloy usi" by Yao Lu, Jun Wang et al.

A functionally graded AlxCoCrFeNi high entropy alloy with a variation in Al concentration along the building direction was in-situ produced using a hybrid powder-bed wire-based direct energy deposition process. A continuous transition from a single FCC structure to a major BCC+minor FCC dual-phase structure was achieved, benefiting from the remelting and reheating process during the deposition. In the FCC→BCC transition zone, the dendritic core region is identified as an FCC matrix decorated by AlNi-rich ordered B2 precipitates. The interdendritic area shows B2 precipitating in the FeCr-rich...

Source: uow.edu.au
"Use of waste glass as fine aggregate in ambient cured alkali-activated" by Yuqin Qian, M. Neaz Sheikh et al. - Vimarsana News

"Use of waste glass as fine aggregate in ambient cured alkali-activated" by Yuqin Qian, M. Neaz Sheikh et al.

This study investigated the feasibility of using two types of waste glass sand as fine aggregate replacement in ambient cured alkali-activated mortars (AAMs). Fly ash (FA) and ground granulated blast furnace slag were used as aluminosilicate source materials to produce the AAMs. The waste glass sand was used to replace 0%, 25%, 50%, 75%, and 100% fine aggregate (by mass) in AAMs. The influences of the use of waste glass sand, for the replacement of fine aggregate, on slump flow, setting time, compressive strength, and flexural strength of ambient cured AAMs were evaluated. It was found that th...

Source: uow.edu.au
"Tungsten doping enhances the mechanical properties of FeCr2V-based med" by Yangfan Wang, Zhiyang Wang et al. - Vimarsana News

"Tungsten doping enhances the mechanical properties of FeCr2V-based med" by Yangfan Wang, Zhiyang Wang et al.

The medium entropy alloys (MEAs) composed of high-melting-point, low-activation elements often demonstrate favorable mechanical properties and reduced activation required for nuclear applications. In this work, novel low activation MEAs of FeCr2V and FeCr2VW0.1 as potential nuclear structural materials have been developed. Thermodynamic calculation was used to guide the MEA design. The materials were fabricated using arc melting and their microstructure and mechanical properties were investigated. The results show that the developed MEAs are characterized by a dual-phase microstructure consist...

Source: uow.edu.au
"Microstructure and mechanical behavior of Ti—Cu alloys produced by sem" by Kaio NIITSU CAMPO, Caio Chaussê de FREITAS et al. - Vimarsana News

"Microstructure and mechanical behavior of Ti—Cu alloys produced by sem" by Kaio NIITSU CAMPO, Caio Chaussê de FREITAS et al.

The mechanical properties of Ti—Cu alloys processed via thixoforming were evaluated. Ti—Cu (25, 27, and 29 wt.% Cu) ingots were produced via arc melting, homogenization at 950 °C for 24 h, and hot-forging at 900 °C, followed by thixoforming at a speed of 8 mm/s after isothermal heat treatment at 1035 °C for 300 s. The thixoformed alloys exhibited good mechanical strength, limited plasticity under tensile loading, and reasonable plasticity under compressive loading. The mechanical strength and plasticity decreased as the Cu content increased as a result of the increasing volume fraction ...

Source: uow.edu.au
"A novel gradient composite material CrMnFeCoNiB2C0.5 prepared by laser" by Da Sun, Jingwen Song et al. - Vimarsana News

"A novel gradient composite material CrMnFeCoNiB2C0.5 prepared by laser" by Da Sun, Jingwen Song et al.

A novel gradient composite of CrMnFeCoNiB2C0.5 was prepared by laser melting deposition (LMD). The heat accumulation during LMD results in thin-walled structure that exhibit significant structural gradients. The material was tested with an ultimate compressive stress of 1.56 ± 0.067 GPa and a compressive strain of 19.17 ± 1.96%. Such materials have the potential to prepare additive manufactured parts with locally-controllable strength and plasticity by simply varying the thermal input only.

Source: uow.edu.au